英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：

specialism    
n. 专门,专攻

专门,专攻

specialism
n 1: the concentration of your efforts on a particular field of
study or occupation
2: the special line of work you have adopted as your career;
"his specialization is gastroenterology" [synonym:
{specialization}, {specialisation}, {specialty},
{speciality}, {specialism}]


请选择你想看的字典辞典：
单词字典翻译
Specialism查看　Specialism　在百度字典中的解释百度英翻中〔查看〕
Specialism查看　Specialism　在Google字典中的解释Google英翻中〔查看〕
Specialism查看　Specialism　在Yahoo字典中的解释Yahoo英翻中〔查看〕

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Stop APs from meshing : r Ubiquiti - Reddit
    Re-terminate the ends on the ones that show meshed Under Settings, go to System, under the Advanced tab there is a Wireless Connectivity section with the option Wireless Meshing Uncheck that I would guess you have a bad cable Reason you can't undo the mesh is because you're actively using it
  • Considerations for Optimal Wireless Mesh Networks - Ubiquiti Help Center
    Mesh connections in UniFi primarily use the 5 GHz band A crowded or noisy RF environment can degrade wireless meshing performance Consider the following: Use DFS channels, which are often less congested Refer to our Optimizing Wireless Client Connectivity guide for more RF best practices
  • Unifi Access Point showing up as connected via mesh
    One of the access points says it's connected via meshing rather than wired I have tried different cables and different ports on the Dream Router as well as resetting the AP and re-adopting but it still says it's connected via Meshing Any reason why this might be the case and how to fix it?
  • Why does a Unifi device show a Parent Device when connected?
    1 The "Parent Device" designation in Unifi indicates the uplink device a particular device is connected to This is particularly relevant for Unifi switches or gateways [1] 2 It may show devices connecting through another access point even if wireless meshing is turned off, possibly due to how the network topology is configured [2] 3
  • ubiquiti unifi - couple of questions about uplinks and meshing
    In my case, it absolutely does not mesh when it is connected to the wired network To test, I disconnected the uplink from the Garage switch, which forced the Carport AP to mesh That took about 3 minutes to start working, and the topology looked like the screenshot below afterwards
  • How to disable AP Uplinking Meshing ? : r Ubiquiti - Reddit
    I noticed yesterday that my AP Lite was uplinked hopped through another access point Both access points are hard wired to my USG and this is normally reflected in the topology view in the dashboard I would like to disable the ability to uplink mesh hop through each other
  • How parent devices work within UniFi: A step by step guide - UniHosted
    Install the UniFi Controller software on your machine or directly deploy a fully managed UniFi Controller with UniHosted Connect the parent device to your internet modem and to other network infrastructure like switches or directly to access points
  • UniFis Advanced Wi-Fi Settings Explained — McCann Tech
    This enables a hidden SSID on each AP, which other APs can connect to Mesh APs rely on wireless backhaul, but otherwise act like a normal UniFi AP They can extend the range of your network, but offer lower throughput If you can’t run Ethernet to all of your APs and need to rely on wireless backhaul, you should leave this enabled
  • UniFi Isolated Devices – Ubiquiti Help Center
    If the isolated AP was previously connected via a wireless mesh, follow these steps: Move the APs closer together A device may become isolated when there isn't sufficient signal strength Factory reset the isolated AP by holding the power button for 10 seconds, or until the light begins flashing
  • Configure Unifi Mesh AP - Philly Community Wireless Docs
    This guide will walk you through configuring a Ubiquiti Access Point AC Mesh ("bunny ears"), which consists of the following steps: Power and factory reset the Unifi AP AC Mesh; Connect the device to your computer, and make sure it has a route to the Internet; Identify AP's IP address and ssh to connect to the device: ssh ubnt@192 168 1 20





中文字典-英文字典  2005-2009