英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：


请选择你想看的字典辞典：
单词字典翻译
esum查看　esum　在百度字典中的解释百度英翻中〔查看〕
esum查看　esum　在Google字典中的解释Google英翻中〔查看〕
esum查看　esum　在Yahoo字典中的解释Yahoo英翻中〔查看〕

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Microphone Pads: Any Tips? - repforums. prosoundweb. com
    Microphone Pads: Any Tips? I don't have the Shure model numbers but can tell you the attenuator is an "H" pad It is five resistors forming the letter "H," with two resistors on each side and one across the middle You can get an XLR barrel adapter (female to male) and put the pad in there Use high quality film resistors (1 4 watt should do with at least 1% tolderance or lower) You would
  • Microphone Pads: Any Tips? - repforums. prosoundweb. com
    Microphone Pads: Any Tips? Microphones working into a lower i p Z may exhibit more distortion (especially older models) Especially if they have a transformer or passive lo-cut, the frequency response may change, too Micpre's seeing a different source Z than the nominal 150-200 ohms may exhibit more noise (has to do with the "optimum source impedance" (OSI) of the first active stage) Effects
  • Mic Pads- When And How To Use Them - ProSoundWeb
    Originally Posted: Sat, 02 September 2006 from a response I recently gave on another forum where the question was asked when to use the -10dB switch on a Neumann U87: The concept of how the pad switch on most transistor condenser mics works, and when to use it, is fairly simple to understand and implement: The -10dB pad switch lowers the amount of voltage coming from the capsule into the
  • Neumann U67 Reissue: Complete Tear Down and Analysis
    That "pads down" the signals coming from the microphone, but not too severely, and it reduces the microphone's self-noise as well as any noise due to interference in the cable, exactly as much as it reduces the wanted signal
  • Replacement for KM84 on snare? - ProSoundWeb
    compasspnt wrote on Fri, 01 February 2008 12:43 Yes, there is a difference between an inline pad and one internal to the microphone The mic preamp would still be breaking up As mentioned, the 55 and 6 have the pads The 5 was really (partially) intended for orchestral use, where no pads are needed A snare drum is very loud
  • ADK S-7b, A real Gem!
    c The -8db pad is a welcome touch and seems to be more "usable" than the typical -10 or -20 db pads commonly available on most mics d The included utility mic clip is usable but undeserving of a mic of this high quality A quality "spider" mount should be used General Sonics: a All three mics seemed to "match" or "favor" the GR preamp
  • Pop Filters: Which Work? Which Suck? The Lowdown
    The whole device is plastic, no ringing Soft rubber pads grip the mic The foam is very open with varied size bubbles in it Two discs supplied, washable Curved to deflect like those old Abbey Road ones I suppose it is hardly surprising that Rycote would do a good pop and suspension, but I really cannot think of anything to improve on this
  • Pop Filters: Which Work? Which Suck? The Lowdown
    The pads are easily washable and dry quickly (hydrophobic) Foam is double the thickness of the Rycote, so is more effective in preventing plosives - but still totally transparent*
  • Mic Pre impedance matching- What Are The Rules? - ProSoundWeb
    When you switch in the resistive pad to such a preamp, then the microphone will see a much more resistive load because the pad resistors interface between the microphone and the input transformer so the mic sees the resistors in the pad as the load Microphone output source impedance is a little bit more difficult concept to initially grasp
  • Reduce noise in U87? - repforums. prosoundweb. com
    One way to optimise a stock U87's signal-to-noise ratio is to run it on the European output strapping, and without pads Consult your owner's manual (also available on the Neumann website) on how to strap the output for 200 Ohms, and how to bypass the inline pads Unless your mic is already strapped that way, this change will yield a minimum of 6dB s n increase





中文字典-英文字典  2005-2009