英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：


请选择你想看的字典辞典：
单词字典翻译
421770查看　421770　在百度字典中的解释百度英翻中〔查看〕
421770查看　421770　在Google字典中的解释Google英翻中〔查看〕
421770查看　421770　在Yahoo字典中的解释Yahoo英翻中〔查看〕

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Configuring EtherChannels - Cisco
    The Dynamic Trunking Protocol (DTP) and the Cisco Discovery Protocol (CDP) send and receive packets over the physical ports in the EtherChannel Trunk ports send and receive PAgP protocol data units (PDUs) on the lowest numbered VLAN
  • 6. 2. 4 Packet Tracer – Configure EtherChannel . . . - ITExamAnswers
    In this lab, you will configure Port Aggregation Protocol (PAgP), a Cisco EtherChannel protocol, and Link Aggregation Control Protocol (LACP), an IEEE 802 3ad open standard version of EtherChannel Before beginning the configuration, review the EtherChannel Configuration Guidelines and Restrictions listed at the end of this activity S1 F0 21
  • etherchannel - Lucid Resource
    For an EtherChannel to become active, all ports in the bundle must be configured identically, regardless if the EtherChannel is being used with access or trunk ports Port settings that must be identical include the following: On trunk connections, the above settings must be configured identically across all participating ports on both switches
  • Solved: Trunking over Etherchannel - Cisco Community
    To change the parameters of all ports in an EtherChannel, apply configuration commands to the port-channel interface
  • Chapter 5: VLAN Trunks and EtherChannel Bundles
    VLAN Trunking Protocol (VTP) - This section provides an overview of how switches become aware of other switches and prevent forwarding loops Dynamic Trunking Protocol (DTP) - This section examines the improvements made to STP for faster convergence
  • What is a requirement to configure a trunking EtherChannel between two . . .
    Explanation: To enable a trunking EtherChannel successfully, the range of VLANs allowed on all the interfaces must match; otherwise, the EtherChannel cannot be formed The interfaces involved in an EtherChannel do not have to be physically contiguous, or on the same module
  • What is a Requirement to Configure a Trunking EtherChannel Between Two . . .
    To configure a trunking EtherChannel, the switches must agree on the trunking parameters, including the encapsulation type and the allowed VLANs Misconfigurations in these settings can prevent the EtherChannel from forming or cause traffic issues
  • Layer 2 Configuration Guide, Cisco IOS XE Amsterdam 17. 2. x (Catalyst . . .
    All ports in an EtherChannel must be assigned to the same VLAN or they must be configured as trunk port The LACP 1:1 redundancy feature is supported on port channel interfaces only The following sections provide information about EtherChannels and the various modes to configure EtherChannels:
  • Etherchannel on Cisco IOS Catalyst Switch - NetworkLessons. com
    Switchport mode (access or trunk) PAgP and LACP will check if the configuration of the interfaces that you use is the same Let’s see if we can configure an Etherchannel We’ll try all three options but start with PAgP If you want to configure PAgP there are two options you can choose from
  • Best practice for a trunk Etherchannel between two Cisco 9300 stack.
    I'm looking for some best practices for setting up a trunked Etherchannel between two 9300 switch stacks We have had issues with Etherchannel setup since moving to the 9300 platform I've always configured a port channel > then setup my interfaces with the following and they work until we got 9300's





中文字典-英文字典  2005-2009